网格划分问题请教高手

我在划分网格时有以下提示,不知什么原因???请教大虾了?
Computing mesh
Running mesher...
C:/Fluent.Inc/bin//../icepak4.3.10/bin.ntx86/mesher.exe C:/Fluent.Inc/V3_CXYH/grid_input C:/Fluent.Inc/V3_CXYH/grid_output -errors C:/Fluent.Inc/V3_CXYH/grid_errors -params C:/Fluent.Inc/V3_CXYH/grid_params -temp_dir C:/Fluent.Inc/V3_CXYH -max_element 10000000
Warning: fan "fan.1.4": shrinking cylinder/fan
Warning: fan "fan.1": shrinking cylinder/fan
Warning: fan "fan.1.5": shrinking cylinder/fan
Warning: fan "fan.1.5.1": shrinking cylinder/fan
Warning: fan "fan.3": shrinking cylinder/fan
Warning: fan "fan.3.1": shrinking cylinder/fan
Warning: fan "fan.3.2": shrinking cylinder/fan
Warning: fan "fan.3.3": shrinking cylinder/fan
Warning: fan "fan.3.1.1": shrinking cylinder/fan
Warning: fan "fan.3.2.1": shrinking cylinder/fan
Warning: fan "fan.3.4": shrinking cylinder/fan
Warning: fan "fan.3.1.2": shrinking cylinder/fan
Warning: fan "fan.3.2.2": shrinking cylinder/fan
Warning: fan "fan.1.4": shrinking cylinder/fan
Warning: fan "fan.1": shrinking cylinder/fan
Warning: fan "fan.1.5": shrinking cylinder/fan
Warning: fan "fan.1.5.1": shrinking cylinder/fan
Warning: fan "fan.3": shrinking cylinder/fan
Warning: fan "fan.3.1": shrinking cylinder/fan
Warning: fan "fan.3.2": shrinking cylinder/fan
Warning: fan "fan.3.3": shrinking cylinder/fan
Warning: fan "fan.3.1.1": shrinking cylinder/fan
Warning: fan "fan.3.2.1": shrinking cylinder/fan
Warning: fan "fan.3.4": shrinking cylinder/fan
Warning: fan "fan.3.1.2": shrinking cylinder/fan
Warning: fan "fan.3.2.2": shrinking cylinder/fan
NODES: 1839312
HEXAS: 1778698
PENTAS: 8764
PYRAS: 230
TETRAS: 92
QUADS: 328636
TRIS: 96
Faces + solids: 962
Computing element quality (face alignment) ...
range: 0.0355633 -> 1
Warning: the worst face alignment in this mesh is 0.0355633.  The bad elements are shown on the screen.  This may cause problems for the solver - please try to fix the mesh if possible before running a solution.
0.0 -> 0.05, 22 values
0.05 -> 0.1, 102 values
Done.
0.95 -> 1, 1323356 values
Computing element quality (quality) ...
range: 2.34429e-007 -> 1
range: 2.34429e-007 -> 1
0.75 -> 0.8, 154169 values
0.75 -> 0.8, 154169 values
0.75 -> 0.8, 154169 values
0.85 -> 0.9, 196221 values
0.85 -> 0.9, 196221 values
0.85 -> 0.9, 196221 values
0.75 -> 0.8, 154169 values
0.85 -> 0.9, 196221 values
Computing element quality (volume) ...
range: 7.64375e-013 -> 1.16129e-006
5.806522615625e-008 -> 1.161296879375e-007, 197523 values
Set x minimum object separation to 0.00015 mm
Set y minimum object separation to 0.00015 mm
Set z minimum object separation to 0.0005 mm
Computing mesh

你这个模型划分的网格质量不好,而且网格数太多。你把你的模型PACK发上来，大家可以帮你调调网格。

是的!!

谢谢!!可我不会发,也不会调?能告诉吗?谢谢

软件“file”菜单下，选择"pack project"，会成生一个TZR文件。
将其压缩，，添加附件。

呵呵！版主真是幸苦了，很好很敬业！