icepak划分网格出错，求解决！【急】

划分网格出错，求解决！
小弟刚学也1个月不到，弄毕业设计。Check: 0 problems were found for 135 objects.应该没 问题了社，怎么划分网格的 时候出错呢？帮忙解释下，不胜感激！
版本：Icepak 4.0.12


Done loading.
Checking objects ---------------
Check: 0 problems were found for 135 objects.
Defined default sizes to be 1/20 of the total.
Set meshing defaults to coarse
Computing mesh
Set minimum object separation to 4.995004995005e-005 m
Writing grid input to file "F:/zjq1/grid_input" ...
14 values were modified by less than 4.995004995005e-005 m to eliminate small gaps
Running mesher...
Pid 1232: C:\Fluent.Inc\icepak4.0\bin.ntx86\mesher.exe F:\zjq1\grid_input F:\zjq1\grid_output -errors F:\zjq1\grid_errors -params F:\zjq1\grid_params -temp_dir F:\zjq1 -max_element 10000000
License check...
Fluent 7 license for ice-mesher obtained
v = 0.0089763 t = 0.0074 v = 0.00991412 t = 0.0074
v = 0.0199117 t = 0.0069 v = 0.0213614 t = 0.0069
v = 0.0089763 t = 0.0074 v = 0.00991412 t = 0.0074
v = 0.0199117 t = 0.0069 v = 0.0213614 t = 0.0069
v = 0.0089763 t = 0.0074 v = 0.00991412 t = 0.0074
v = 0.0199117 t = 0.0069 v = 0.0213614 t = 0.0069
171168 real hexas
1062 real prisms
1664 real pyramids
1664 real tetrahedra
worst face alignment 0.00452
38111 quads
617 tris
Done.
Warning: block "block.4.2": object volume 7.833e-006, in mesh 7.43924e-006
Warning: block "block.4.2": bounds -0.0345 0.0295 0.155 - 0.0345 0.033 0.195
Warning: block "block.4.2": versus -0.0345 0.0295 0.155 - 0.0345 0.033 0.195
Warning: block "block.4.2": bounds volume 9.66001e-006
Warning: block "block.9": object volume 4.08911e-005, in mesh 3.30462e-005
Warning: block "block.9": bounds -0.0395 -0.0205 0 - 0.0395 0.0205 0.0522
Warning: block "block.9": versus -0.0395 -0.0205 0 - 0.0395 0.0205 0.0522
Warning: block "block.9": bounds volume 0.000169076
Warning: block "block.11": object volume 4.00091e-005, in mesh 3.20849e-005
Warning: block "block.11": bounds -0.02052 0.0765 0.09386 - 0.02052 0.127 0.173
Warning: block "block.11": versus -0.02052 0.0765 0.09386 - 0.02052 0.127 0.173
Warning: block "block.11": bounds volume 0.000164019
Loading mesh information ...
NODES: 181878
HEXAS: 171168
PENTAS: 1062
PYRAS: 1664
TETRAS: 668
QUADS: 38111
TRIS: 617
Faces + solids: 257
Done.
Mesh has already been made conformal
Computing element quality (face alignment) ...
range: 0.00452323 -> 1
Warning: the worst face alignment in this mesh is 0.00452323.  The bad elements are shown on the screen.  
This may cause problems for the solver - please try to fix the mesh if possible before running a solution.
0.0 -> 0.05, 56 values
0.05 -> 0.1, 167 values
Done.
zjq.JPG (75.39 KB)




zjq.rar (16.34 KB)

  怎么每人弄的懂?

细小网格的问题吧

：那该怎么弄呢？

看了你的模型，发现你建的模型有问题！你大量使用了多边形，其实本身不用多边形也能实现，而且局部地方有好多小间隙！

樓主的模型確實有大量的使用多邊形來建模，但這樣對模擬結果有影響嗎?