点RUN后出现
error:can't read "interface_zones_to_merge(0 1 0 0)":no such element in array
打开Stack trace：
Error at Mon May 17 21:10:01 中国标准时间 2010 ------------------------
Program: Icepak
Compiled: Tue Oct 13 7:17:42 PM CDT 2009
can't read "interface_zones_to_merge(0 1 0 0)": no such element in array
while executing
"lindex $interface_zones_to_merge($zm1) 0"
(procedure "write_case_unstruct_couplings" line 53)
invoked from within
"write_case_unstruct_couplings $scr"
(procedure "write_case" line 214)
invoked from within
"write_case $file"
(procedure "solve_writedata_uns" line 17)
invoked from within
"solve_writedata_uns $casfile"
(procedure "solve_start_one" line 226)
invoked from within
"solve_start_one $batch 0"
(procedure "solve_start" line 195)
invoked from within
"solve_start"
invoked from within
".solve_run.bottom.0 invoke"
("uplevel" body line 1)
invoked from within
"uplevel #0 [list $w invoke]"
(procedure "tkButtonUp" line 9)
invoked from within
"tkButtonUp .solve_run.bottom.0
"
(command bound to event)
终于RUN起来了，虽然还报错：
Error: chip-exec: function "fan_pressure" not found
Error: chip-exec: function "update_fan" not found
离心风扇已设风压流量了呀。。
RUN的过程一直出现
Warning - mass flow of 0.00110896 exceeds max value on fan of 0.000665446
不过收敛曲线不错，就是温度曲线先是收敛但到了40步后开始上翘后才开始缓慢收敛。。
今天新建的模型带有Nonuniform的polygon，调整好网格，网格各项指标都很好
可是运算开始时FLUENT出现160多个WARNING，最后还出现out of memory，然后就不能继续了
网格150W，电脑4G内存肯定够用，请问谁知道是什么原因啊？？？
最后面那个malloc DO IW Tmp和Resize_Vector_AMG_Chunk是什么意思
WARNING: The mesh contains high aspect ratio hexahedral
or polyhedral cells.
The default algorithm used to compute the wall
distance required by the turbulence models might
produce wrong results in these cells.
Please inspect the wall distance by displaying the
contours of the 'Cell Wall Distance' at the
boundaries. If you observe any irregularities we
recommend the use of an alternative algorithm to
correct the wall distance.
Please select /solve/initialize/repair-wall-distance
using the text user interface to switch to the
alternative algorithm.
> (if (err-protect (ti-menu-load-string "s i i")) (pp "Ok") (begin (close-output-port (open-output-file "***.uns_out")) (close-output-port (open-output-file "***.uns_error"))))s i i
Warning: Could not correct the face handedness for face 38392, zone 807
Warning: Could not correct the face handedness for face 38399, zone 807
Warning: Could not correct the face handedness for face 38406, zone 807
Warning: Could not correct the face handedness for face 38415, zone 807
Warning: Could not correct the face handedness for face 38424, zone 807
......... 一
......... 百
......... 六
......... 一
......... 十
......... 个
Warning: Could not correct the face handedness for face 39981, zone 807
Warning: Failed to correct face handedness of 159 out of 159 left-handed faces on the sliding interface zone 807.
"Ok"
Warning: ST_Malloc: out of memory.malloc_storage: unable to malloc DO IW Tmp, size 12940308, t 845, myid 1000000.
Error: 1000000: Failed to allocate 27.36MB memory (..\\..src.amgif.c:1049)
Error:
Out of memory in Resize_Vector_AMG_Chunk
Error Object: #f
#f
最后跳出Information对话框
Warning: An error or interrupt occurred while reading the journal file.
Some commmand may not have been completed.